Resin print exposure calibration calculator

Jacobs working curve using experimentally supplied penetration depth and critical dose.

3d-printing-resin-exposure.napkin / editable

SCENARIO COMPARISON

Compare the numbers.

This source describes an analytical model. Its quantities and checks are the view.

Scenario	dosemJ/cm^2	cureDepthmm
	10	0.0693147
	10	0.0554518

All calculated quantities are listed with the inputs. Switch to Source to inspect the equations.

SCENARIOS / CALCULATED VALUESSAME SOURCE

Change an input to see the consequences.

cure depth target0.07 mm✓ passes

BASELINE INPUTS

penetration0.1 mmcriticalDose5 mJ/cm^2irradiance5 mW/cm^2exposure2 s

CALCULATED

dose10 mJ/cm^2

cureDepth0.069315 mm

Edits change the baseline source.

THE SOURCE

Edits below update the same model.

# Resin print exposure calibration
# Scope: Jacobs working curve using experimentally supplied penetration depth and critical dose.
# Status: illustrative worked example; engineering review pending.
# Inputs are example values. Checks are editable example requirements, not standards.

penetration = 0.1 mm
criticalDose = 5 mJ/cm^2
irradiance = 5 mW/cm^2
exposure = 2 s

dose := irradiance*exposure [mJ/cm^2]
cureDepth := penetration*log(dose/criticalDose) [mm]

check cure depth target: cureDepth >= 0.05 mm

scenario alternative: penetration = 0.08 mm

Calculated from your source · not saved

Baseline · Baseline

cure depth target0.07 mm ✓ passes

alternative · alternative

cure depth target0.06 mm ✓ passes

Illustrative first-order example. Checks are editable requirements, not design standards. The broader topic may require additional equations, data, and validation.

Formula and units

This example uses the following equations. Input names and units match the editable source above.

dose: dose = irradiance*exposure [mJ/cm^2]
cure depth: cureDepth = penetration*log(dose/criticalDose) [mm]

Original worked example

These are the baseline values in the downloadable source. Edits above let you test your own values.

Given

penetration: 0.1 mm
critical dose: 5 mJ/cm^2
irradiance: 5 mW/cm^2
exposure: 2 s

Calculated

dose: 10 mJ/cm^2
cure depth: 0.0693147 mm

Assumptions and limits

Jacobs working curve using experimentally supplied penetration depth and critical dose.

The requirement checks use the limits written in this example. Passing a check does not establish that the model covers every load, material behavior, or operating condition in a real design.

Download this .napkin example ↓

Take it further with your agent

Napkin keeps the inputs, equations, checks and assumptions together in one study. Your agent sets it up; you change the numbers.

Try with Claude ↗

codex 'Use Napkin (https://napkin.engineering/mcp, or the local Napkin plugin) to build a study: Resin print exposure calibration. Inputs: measured cure response; layer target; working-curve parameters. Outputs: candidate exposure; cure-depth estimate. Model scope: Geometry plus explicitly calibrated machine and material parameters. Read napkin_capabilities and the current snapshot. Ask me for the values that matter, label assumptions with units, author .napkin source, validate it and apply it with napkin_source using the current revision, then open the study. Add checks for the limits I supply. Keep unsupported analyses explicit.'

Claude needs the Napkin connector; Codex needs the Napkin plugin. Set up your agent ↗

The broader study

The topic brief below describes the broader scope. The worked example above states the particular calculation it implements.

Inputs: measured cure response, layer target, working-curve parameters
Outputs: candidate exposure, cure-depth estimate
Modes: calculate, compare, sweep
Drawing: Part, orientation and layer preview

EXECUTABLE WORKED EXAMPLE · FIRST-ORDER MODEL · CHECK THE SCOPE & ASSUMPTIONS